How To Fix Canon Printer Error 6c10? Easy Solution

Canon Printer Error 6c10 is a “CAM sensor error”. But why the error happens in the printer. Well, the error occurs arrive in the printer when the user pressed the button ON green light flashes. After a time both the buttons flash alternatively. To correct this error or to vanish it completely from the printer, most of the time users need to reinstall the printer drivers. Canon printer gives good performance without any doubt, they have advance features as well as build on high technology by the professionals. Today, a printer comes in various use, now the user doesn’t need to go to any printing shops. They can get their pro like prints at home, scan their images and documents, and apart from this, they can also get duplex copies as much as they want and also fax documents.

But because of the errors that occur in canon printers can make them fail to perform. Therefore, this can make users irritated. However, you don’t need to worry because through this blog you will learn how to solve the 6c10 error in the canon printer.

So, let us start our guide!

Fix Canon Printer Error 6c10 With Easy Steps

Step 1:

  • Move Printerhead to the center
  • Disconnect the printer and then check on the right side- is the purge unit in the right condition.
  • No piece of paper should be there.

Step 2:

  • Reset your printer
  • Now power off and then wait for a few minutes.
  • Now switch on the printer
  • Keep holding the Resume button for 15 to 20 seconds.

Step 3:

  • Switch off your Canon printer.
  • Now open its door.
  • Power on your device.
  • When you see that the cartridges are in the center then close the door.

Step 4:

  • Open the lid and allow your ink cartridge carrier to center it.
  • By looking at the right side you will notice a row of white rollers behind the carrier.
  • At the end of the rollers, you will see a small, clear piece of plastic that sticks up.
  •  Now you need to take a small piece of towel and slowly wipe all of the ink.
  • Remember to you cotton cloth or paper towel.
  • Once the rollers are cleaned move on to the ink pad section.
  • About a 1 or 2 inches in the direction of the printer from that piece of plastic, you will see a small square. And about half inches per side you will find a small form pad.
  • This is the place where you will see that the excess of ink gets collected. Now you need to soak it.
  • Use another paper towel and press it into its foam. Keep doing that until the paper towel is no stop collecting the ink.
  • Now close the lid and power off the printer then turn it back on.

Step 5:

Next, you need to clean your Canon printer’s Printerhead. For this, you can take the help of your Canon printer manual and read the guide from the manual and follow the step by step instructions.

Step 6:

  • Remove the casing and look for any micro switch that is being pressed by one of the purge unit cams.
  • Now you need to clean it.

Reset The Ink Absorber Counter:

  1. Switch off the printer.
  2. Press and hold the Resume button for a few minutes.
  3. Now press and hold the Power button at the same time. It will turn On the green LED light.
  4. Hold the power button and release the resume button
  5. Press the Resume button two times, and then release both the buttons.
  6. Now press the resume button four-time and then immediately press the Power button.

This sequence of pressing and releasing power and resume button will reset the ink absorber counter on the printer. Now after this switch off the printer unplug it and then plug it again and power on the printer. Now check if the printer is out of this 6c10 error or not.

Conclusion:

After the whole process restarts your printer and takes a closer look while printing. If it prints perfectly then the error is solved, but if it miss-print or deny from printing, it means the error is still present.

If the above solutions didn’t work for you, then you can try reaching to the experts, to take their help. As Canon printer has amazing support, and all the executives there are well-trained and experienced. You just need to contact them and tell them about the error you are facing, and then they will answer all your queries. They are present just a call away and stay active 24×7 to assist you in every issue related to Canon Printer.